Multi-Function Electronic Wind and Water Level Control System

The CWW-002 is a cost-effective controller that provides both multiple stage wind and water level control capability.
• PLC based and pre-programmed.
• Mounted in NEMA-4X enclosure.
• 4 x 12 digital operator display.
• Operates on 100-240 volt, 50 or 60 hertz power.
• Single and 2-stage wind control.
• Supplied with CWS-075 wind speed sensor.
• Dual level water level control and low water cut-off. (Order CWL-302P
probe and sensor housing separately.)
• Underwriters Laboratories Listed for safety.

Wind Speed Sensor

The CWS-075 is designed for use with both the CPL-3000T Fountain Control Panel and the multi-function CWW-002 Control System.

• Rotating cup type anemometer.
• Aluminum construction with stainless steel bearings and an integral 30 foot cable.
• Rated for 100 MPH wind speed with a 1 MPH starting threshold.
• Adapts to 3/4” PVC conduit.

Note: Anemometer should be mounted in an area which experiences the same wind conditions as the water feature

Single Function Water Level Control

• Single function operation – water fill or low water cut-off.
• Housed in a NEMA-4X enclosure.
• Operates on 100-240 volt, 50 or 60 hertz power.
• Provides safe 10 volt signal to sensor probe.
• Supplied with sensor, (select appropriate probe housing).
• Pre-wired and tested.
• Requires a 120 VAC Class A GFCI protected power supply in    the USA.
• Underwriters Laboratories Listed for safety.

Dual Function Water Level Control

• Dual function operation – water fill and low water cut-off.
• Housed in a NEMA-4X enclosure.
• Operates on 100-240 volt, 50 or 60 hertz power.
• On-Off-Auto switch allows easy over-ride for pool    maintenance.
• Water fill and low water cut-off pilot lights furnished to    indicate system status.
• Provides safe 10 volt signal to sensor probe.
• Supplied with dual function sensor and 30 feet of integral    cable (select appropriate
   probe housing from pg. 89).
• Pre-wired and tested.
• Requires a 120 VAC Class A GFCI protected power supply in    the USA.
• Underwriters Laboratories Listed for safety.

Conduit Mounted Sensor Housing

The CWL-002C provides a low profile for in pool mounting of sensor probes.

• Spun brass cover with natural finish.
• Cast bronze base with 1/2” threaded conduit connection.
• Sensor adjustment range is 1/4” for dual and 1-1/4” for   single function probes.

Wall Mounted Sensor Housing

The CWL-002W offers an unobtrusive wall mounted configuration.

• Cast bronze housing with 1/2” threaded conduit connection.
• Cast bronze face plate with natural finish.
• Sensor adjustment range is 1/2” for dual and 1-1/2” for single function probes.
• For optional integral waterstop flange, add suffix –WS to catalog number.

Wall Mounted Overflow and Sensor Housing

The flush wall mounted CWL-002WD combines a sensor mounting housing with an adjustable overflow drain fitting.

• Cast bronze housing with 1/2” threaded conduit connection   and 3” FPT drain outlet.
• Cast bronze face plate.
• Adjustable internal overflow standpipe
• Sensor adjustment range is 1/2” for dual and 1-1/2” for   single function probes.
• For optional integral waterstop flange, add suffix –WS to   catalog number.

Single Function Water Level Control

The RW-56-1 is designed to use a resistive type probe with no moving parts.

• Single function operation – water fill or low water cut-off.
• Housed in a NEMA-4X enclosure.
• Operates on 100-240 volt, 50 or 60 hertz power.
• Provides a safe 10 volt signal to sensor probe.
• Sensor is replaceable and may be trimmed to set water   level.
• Supplied with 100 feet of sensor wire.
• Probe housing is cast bronze and copper with red brass vent   and equalizer tubes.
• Pre-wired and tested.
• Requires a 120 VAC Class A GFCI protected power supply in   the USA.
• Underwriters Laboratories Listed for safety.

Flush Mounted Underwater Junction Box

The LJN-1C junction box may be used where probe or sensor runs exceed the standard 30 foot cord length.

• Cast bronze construction with stainless steel fasteners.
• Black neoprene lid gasket.
• Underwriters Laboratories Listed for underwater and dry   location.

Note: It is recommended that a potted junction box be installed in the conduit run connecting water level sensors to control panels. This will prevent moisture migration from the pool to the control panel.

Solenoid Fill Valve

The RVS Series solenoid fill valve is simple and easy to clean and maintain.

• For use with electronic water fill systems.
• Die cast brass construction with threaded connections.
• 120 volt solenoid is standard.
• Solenoid is Underwriters Laboratories Recognized.